10 best arduino mega ramps 1.4 for 2019
Finding your suitable arduino mega ramps 1.4 is not easy. You may need consider between hundred or thousand products from many store. In this article, we make a short list of the best arduino mega ramps 1.4 including detail information and customer reviews. Let’s find out which is your favorite one.
Best arduino mega ramps 1.4
![[Sintron] 3D Printer Controller RAMPS 1.4 Arduino Mega Pololu Shield for Reprap Prusa Mendel Arduino Mega2560](https://images-na.ssl-images-amazon.com/images/I/51PgdHqWdyL.jpg)
1. RAMPS 1.4 Controller + MEGA2560 R3 board + 5pcs Soldered A4988 Stepper Motor Drivers + 5pcs Heat Sinks + 19pcs Jumpers with USB Cable For Arduino RepRap 3D Printer Kit
Feature
RAMPS interfaces an Mega with the powerful MEGA platform and has plenty room for expansionMega 2560 control board is an ATmega2560 as core micro-controller development board itself has 54 digital I/O input/output terminals (14 can be used as PWM outputs), 16 simulation than the input side, group 4 UARTs (hardware serial ports), 16 MHz crystal
RAMPS is designed to fit the entire electronics needed for a RepRap in one small controller for a lower cost and a smaller size.
With the boot-loader, download the program directly via USB without having to go through other external writer
After connecting this panel to your RAMPS, you don't need your pc any more. The smart controller supplies power for your SD card. All actions like calibration, axes movements can be done by just using the rotary encoder on the smart controller
Description
Specifications:
RAMPS 1.4 Size: 9.1 x 5.9cm / 3.58 x 2.32"
Mega R3 2560 Size: 10.8 x 5.5cm / 4.25 x 2.16"
A4988 Color: Green
A4988 Quantity: 5pcs
1 x RAMPS 1.4 Board
1 x Mega 2560 R3 Board
5 x Soldered A4988 Drivers
5 x Heat Sinks
1 x USB Cable
19 x Jumpers
2. OSOYOO 3D Printer Kit with RAMPS 1.4 Controller + Mega 2560 board + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display Controller with Adapter For Arduino RepRap
Feature
3D printer Kit guide: 3D printer Kit guide: http://osoyoo.com/driver/3D%20printer%20instructions.pdf3D Printer Controller RAMPS 1.4 interfaces an Arduino Mega2560 board. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion
With LCD 12864, you can easy connect it to your Ramps board using the "smart adapter" included. After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.
It is designed to fit the entire electronics needed for a RepRap in one small package for low cost
We are professional factory on making all electronics components based on Arduino and Raspberry Pi. And we also have processional engineer team to offer you tutorials which you can start from beginning. all documents (including code)
Description
3D printer Kit guide: http://osoyoo.com/driver/3D%20printer%20instructions.pdf
Caution:
1) The max power supply for these ramps is 12V and the max watts is about 180W. The max watts for the hotbed is about 100W and the max temperature is just 50 degree Celsius.
2) Do not plug or unplug and wire or module when power is on, do not even touch the board when power is on or your hand has static charge(you can remove static charge by touching metal tap) .
3) Always double check power wire is properly installed. If you do not follow above move, you may damage the control board and your 3D printer.
4) Pls confirm the A4988 driver install correctly on Ramps1.4 board.
5) The endstop pins are Signal-GND-VCC, instead of VCC-Signal-GND like the rest of RepRaps boards. Make sure to wire them correctly. This is done to allow squeezing fatter traces on the printable board.
6) Don't secure Arduino/Ramps with conductive screws through both mounting holes. The screw may cut into the positive trace creating a HIGH current short.
7) Test all electronics thoroughly before placing into service.
8) Do not leave power supplied to electronics unattended, or run machines unattended due to the risk of fire and malfunction.
9) Once you start putting electricity into your RepRap - even at just 12 volts - you have to take basic, common sense precautions to avoid fires. Just in case these fail. test your workshop smoke detector.
Product Specification:
1) Marlin firmware update: Arduino IDE 1.5.X
2) This kit consists of a RAMPS 1.4 shield, an Mega 2560 board, five Stepper drivers and a LCD. It can control up to 5 stepper motors with 1/16 stepping precision and interface
3. 3D Printer Controller Kit for Arduino Mega 2560 Uno R3 Starter Kits + RAMPS 1.4 with Upgraded Mosfet + 5pcs A4988 Stepper Motor Driver + LCD 12864 for Arduino Reprap (14 Items)
Feature
3D Printer Controller Kit Mega 2560 R33D Printer Controller RAMPS 1.4 interfaces an Arduino Mega2560 board. The modular design includes a plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgradeability and expansion
LCD 12864 Graphic Smart Display Controller and the A4988 Stepper Motor Driver
3D Printer Controller 100% compatible with Arduino RepRap
Detailed tutorials including project introduction and source code are provided for free, just contact us by Email
Description
Difference between 2016 and 2017 Version 2016 Old MOSFET IC Model : PDF55N06 VDSS:60V ID:55A 2017 New MOSFET IC model: HM60N06 VDSS:60VID:60A, more durable and safety. Product Features: 1) Mega 2560 R3 2) 3D Printer Controller RAMPS 1.4 with high-quality MOSFET Designed to fit the entire electronics needed for a RepRap in one small package for low cost, interface with the powerful Arduino-compatible Mega platform with plenty space for expansion. 3) A4988 Stepper Motor Driver A complete micro-stepping motor driver with built-in translator for easy operation 4) LCD 12864 Graphic Smart Display Controller Contains an SD-Card reader, a rotary encoder, and a 128 x 64 dot matrix LCD display. Easy to connect it with your Ramps board using the "smart adapter" included. Package List: (1) RAMPS 1.4 x 1 (2) Mega 2560 R3 x 1 (3) A4988 Stepper Motor Driver with Heatsink x 5 (4) LCD 12864 Graphic Smart Display Controller x 1 (5) Smart Adapter x 1 (6) Cable x 2 (7) USB Cable x 1Caution: 1.Please read the technical parameters of the board carefully before you use it; 2.Only connect the mega2560 board with the computer via USB cable while programming firmware; 3.Reversed connection of the power supply or the motor driver may cause the board burning, please confirm again before power on; 4.Only power on the Ramps 1.4 while testing the product, supply power to the mega2560 board may cause burning the board; 5.Select the appropriate load according to the board voltage/current requirement,if the work current exceeds the load of the board which may cause the board burning. If you have any questions and need any technical help, please be free to contact us, we will try our best to help you.4. kuman 3D Printer Controller Kit for Arduino Mega 2560 Uno R3 Starter Kits +RAMPS 1.4 + 5pcs A4988 Stepper Motor Driver + LCD 12864 for Arduino Reprap K17
Feature
Update High Quality Ramp Board by changing MOSFET: old MOSFET IC Model : PDF55N06 SpecificationVDSS:60V ID:55A New MOSFET IC model: HM60N06 SpecificationVDSS:60V ID:60A HM60N06 current up to 60AMore safety3D Printer Controller RAMPS 1.4,A4988 Stepper Motor Driver
LCD 12864 Graphic Smart Display Controller
3D Printer Controller 100% compatible with Arduino RepRap
Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents
Description
Product Specs:(1) Mega 2560 R3
(2) 3D Printer Controller RAMPS 1.4 It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.
(3) A4988 Stepper Motor Driver
A4988 is a complete microstepping motor driver with built-in translator for easy operation
(4) LCD 12864 Graphic Smart Display Controller
This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the "smart adapter" included.
Update High Quality Ramp Board by changing MOSFET: old MOSFET IC Model : PDF55N06 SpecificationVDSS:60V ID:55A New MOSFET IC model: HM60N06 SpecificationVDSS:60V ID:60A HM60N06 current up to 60AMore safety
Package List:
(1) RAMPS 1.4 x 1
(2) Mega 2560 R3 x 1
(3) A4988 Stepper Motor Driver with Heatsink x 5
(4) LCD 12864 Graphic Smart Display Controller x 1
(5) Smart Adapter x 1
(6) Cable x 2
(7) USB Cable x 1
Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents.
Note:
1. You just need to connect the computer with Mega 2560 via USB download cable when burning firmware.
2.The chip and circuit may be burnt when the power and motor driver board reversed, so please confirm twice before powering.
3.You just need to power Ramps 1.4 when testing.If you power Mega 2560, the chip will be burnt easily. So please read the introduction carefully and avoid the board being burnt due to the wrong operation.
5. Longruner 3D Printer Kit RAMPS 1.4 Controller Board + 5pcs A4988 StepStick Stepper Motor Driver Module + Heat Sink for 3D Printer Reprap, CNC Machine or Robotics
Feature
Flexible: 1pcs RAMPS 1.4 Controller Board+ 5pcs A4988 Stepstick Stepper Motor Driver Module with Heat Sink on your Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.RAMPS 1.4 expansion board as a driver expansion board, can be used for engraving machines, 3D printers and it is a total of five slots, can drive five A4988 stepper motor.
Update High Quality Ramp Board by changing MOSFET: old MOSFET IC Model : PDF55N06 * SpecificationVDSS:60V ID:55A New MOSFET IC model: HM60N06 SpecificationVDSS:60V ID:60A HM60N06 current up to 60AMore safety Each road stepper motors only need two IO ports.
Stepper motor wiring as follows: 2A, 2B is a group (red, green), 1A, 1B is a group (blue, yellow), if want to change direction, can be change the position of one group , for example 2A, 2B mutually exchanged.
Using This suite (1pcs RAMPS 1.4 Controller Board+ 5pcs A4988 Stepstick Stepper Motor Driver Module with Heat Sink on your Arduino-compatible MEGA shield for easy service,part replacement,upgrade-ability and expansion.
Description
RAMPS 1.4 Controller BoardUpdate High Quality Ramp Board by changing MOSFET:
Old MOSFET IC Model : PDF55N06; Specification: VDSS: 60V; ID:55A
New MOSFET IC model: HM60N06; Specification: VDSS: 60V; ID: 60A
HM60N06 current up to 60A,More safety
Expandable to control other accessories.
3 Mosfets for heater / fan outputs and 3 thermistor circuits.
Fused at 5A for additional safety and component protection
Heated bed control with additional 11A fuse.
Fits 5 Pololu stepper driver boards.
Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs.
I2C and SPI pins left available for future expansion.
All the Mosfets are hooked into PWM pins for versatility.
Servo style connectors are used to connect to the end stops, motors, and LEDs. These connectors are rated for 3A, very compact, and globally available.
SD Card add on available.
LEDs indicate when heater outputs on.
Option to connect 2 motors to Z for Prusa Mendel.
A4988:
Simple step and direction control interface.
Can interface directly with 3.3 V and 5 V systems.
Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout.
Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step.
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use
voltages above your stepper motor's rated voltage to achieve higher step rates.
Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
45 V maximum supply voltage.
Built-in regulator.(no external logic voltage supply needed)
Package include:
1 * RAMPS 1.4 controller board
5 * A4988 Step stick Driver
5 * Heat Sink
6. HESAI RAMPS 1.4 Controller Control Panel for Reprap Mendel Prusa 3D Printer Support Arduino Mega 2560 Devlepment Board
Feature
Fully assembled & tested, no soldering requiredDesigned to fit the entire electronics needed for a RepRap in one small package for low cost.
Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.
Description
Description:
RepRap Mega Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.
It has Cartesian robots and regulations of the extruder .
Extended to control other accessories.
Heater / MOSFET outputs and three fan thermistor circuit.
Integration of additional security 5A and component protection
Control of additional heating bed 11A fuse
Suitable for 5 Pololu stepper driver board
Pololu board pin socket, so they can be easily replaced or removed for future designs .
I2C and SPI pins left for future expansion.
Hooked into all MOSFET PWM pin versatility.
Servo type connector is used to connect to the end stop , the motor and the light-emitting diodes. These connectors are gold-plated , rated current of 3A, very compact.
On the SD card to add - is now available from the Kliment - Sdramps
LED indicate when the heater output
Option 2 motors connected to Z Prusa Mendel
Package List:
1x Ramps 1.4 Controller
7. HiLetgo RAMPS 1.4 Control Panel 3D Printer Control Board Reprap Control Board Support Arduino Mega 2560
Feature
The fifth stepper motor output port can be customized as a Z-axis motor or a second extruder.Can be extended to control other accessories.
Three field effect transistors, three heater / fan output ports, three thermistor circuits.
Heated bed control, extra 11A fuse.
Pololu board foot socket, can be easily replaced or removed.
Description
Description:RepRap Mega Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
Features
1.It has Cartesian robots and regulations of the extruder .
2.Extended to control other accessories.
3.Heater / MOSFET outputs and three fan thermistor circuit.
4.Integration of additional security 5A and component protection.
5.Control of additional heating bed 11A fuse.
6.Suitable for 5 Pololu stepper driver board.
7.Pololu board pin socket, so they can be easily replaced or removed for future designs.
8.I2C and SPI pins left for future expansion.
9.Hooked into all MOSFET PWM pin versatility.
10.Servo type connector is used to connect to the end stop , the motor and the light-emitting diodes. These connectors are gold-plated , rated current of 3A, very compact.
11.On the SD card to add - is now available from the Kliment - Sdramps.
12.LED indicate when the heater output.
13.Option 2 motors connected to Z Prusa Mendel.
Package Included
1* RAMPS 1.4 Control Panel 3D Printer Control Board Reprap Control Board
8. Quimat 3D Printer Controller Kit for Arduino Mega 2560 Uno R3 Starter Kits + RAMPS 1.4 with Upgraded Mosfet + 5pcs A4988 Stepper Motor Driver + LCD 12864 for Arduino Reprap
Feature
3D Printer Controller Kit Mega 2560 R33D Printer Controller with new upgraded RAMPS 1.4,high quality MOSFET HM60N06 with up to 60A work current,more durable and safety
LCD 12864 Graphic Smart Display Controller and the A4988 Stepper Motor Driver
3D Printer Controller 100% compatible with Arduino RepRap
Detailed tutorials including project introduction and source code are provided for free, just contact us by Email
Description
Difference between 2016 and 2017 Version 2016 Old MOSFET IC Model : PDF55N06 VDSS:60V ID:55A 2017 New MOSFET IC model : HM60N06 VDSS:60V ID:60A,more durable and safety Product Features: 1).Mega 2560 R3 2).3D Printer Controller RAMPS 1.4 with high quality MOSFET Designed to fit the entire electronics needed for a RepRap in one small package for low cost, interface with the powerful Arduino-compatible Mega platform with plenty space for expansion. 3).A4988 Stepper Motor Driver A complete micro-stepping motor driver with built-in translator for easy operation 4).LCD 12864 Graphic Smart Display Controller Contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. Easy to connect it with your Ramps board using the "smart adapter" included. Package List: RAMPS 1.4 x 1 Mega 2560 R3 x 1 A4988 Stepper Motor Driver with Heatsink x 5 LCD 12864 Graphic Smart Display Controller x 1 Smart Adapter x 1 Cable x 2 USB Cable x 1 Note: 1.Please read the technical parameters of the board carefully before you use it 2.Only connect the mega2560 board with the computer via USB cable while programming firmware; 3.Reversed connection of the power supply or the motor driver may cause the board burning, please confirm again before power on; 4.Only power on the Ramps 1.4 while testing the product, supply power to the mega2560 board may cause burning the board; 5.Select the appropriate load according to the board voltage/current requirement,if the work current exceeds the load of the board which may cause the board burning Any questions or concerns, please feel free to contact us,we are looking forward to serving you again9. BIQU MKS-Base V1.6 Plate Controller Board for 3D Printer Ramps 1.4
Feature
Arduino MEGA compatible Atmega2560 and FT232 processors are compatible with all RAMPS class firmwareFirmware can use the same configuration as ramps1.4
Easy DISPLAY + SD-CARD connector,RepRapDiscount SmartController compatible pin header on board
Easy connect MKS TFT on AUX-1
3x temperature ADC connectors for thermistors
Description
Product Feature
MKS BASE is a feature rich all-in-one electronics solution for Reprap and other CNC devices. It features an onboard ATmega2560. Its five motor outputs are powered by A4982 stepper drivers. The board can use the same firmware as Ramps1.4. MKS BASE is designed to be flexible in the user's power source availability, allowing any power supply from 12V-24V.
Product Description
1, up to 5 motor driver with A4982
2, 4x PWM capable power mosfet outputs with voltage selector for 3, MainPower.(Bed,Extruder0,Extruder1, Fans)
3, 4 layers PCB, optimize heat dissipation.
4, 6x end stop connectors with power supply Xmin/Xmax/Ymin/Ymax/Zmin/Zmax
5, Recoverable fuse for short-circuit protection.
Packing Included:
1 *MKSBASE V1.6
1*USB
10. [Sintron] 3D Printer Controller RAMPS 1.4 Arduino Mega Pololu Shield for Reprap Prusa Mendel Arduino Mega2560
Feature
(1) 3 mosfets for heater / fan outputs and 3 thermistor circuits.(2) Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs.
(3) All the Mosfets are hooked into PWM pins for versatility.
(4) Servo style connectors are used to connect to the endstops, motors, and leds. These connectors are gold plated, rated for 3A, very compact, and globally available.
(5) Fused at 5A for additional safety and component protection , Heated bed control with additional 11A fuse .
Description
OverviewThe RepRap Arduino-compatible MEGA Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.
Features
(1) It has provisions for the cartesian robot and extruder.
(2) Expandable to control other accessories.
(3) 3 mosfets for heater / fan outputs and 3 thermistor circuits.
(4) Fused at 5A for additional safety and component protection .
(5) Heated bed control with additional 11A fuse .
(6) Fits 5 Pololu stepper driver board .
(7) Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs.
(8) I2C and SPI pins left available for future expansion.
(9) All the Mosfets are hooked into PWM pins for versatility.
(10) Servo style connectors are used to connect to the endstops, motors, and leds. These connectors are gold plated, rated for 3A, very compact, and globally available.
(11) USB type B receptacle .
(12) SD Card add on available .
(13) LEDs indicate when heater outputs on .
(14) Option to connect 2 motors to Z for Prusa Mendel .
Recent Comments