Top 10 best amp jl
Finding the best amp jl suitable for your needs isnt easy. With hundreds of choices can distract you. Knowing whats bad and whats good can be something of a minefield. In this article, weve done the hard work for you.
Best amp jl
1. JL Audio JX1000/1D 1000 Watt RMS Monoblock Class D Car Amplifier
Feature
JX Series Monoblock Amplifier 500 rms @ 4ohms 750 rms @ 3ohms and 1000 rms @ 2ohmsUnregulated PWM switching type power supply
Variable Bass Boost (0 to +12 dB bass boost centered at 45 Hz)
Soft start turn-on prevent clicking and popping when system turns on
Dimensions: 11"L x 7-3/4"W x 2"H
Description
JL Audio JX1000/1D 1000 Watt RMS Monoblock Class D Car Amplifier OPEN BOX2. JL Audio JX400/4D 4-channel car amplifier 70 watts RMS x 4
Feature
RMS Power Rating (14.4V): 4 ohms: 70 watts x 4 chan. | 2 ohms: 100 watts x 4 chan. | Bridged, 4 ohms: 200 watts x 2 chan.RMS Power Rating (12.5V): 4 ohms: 50 watts x 4 chan. | 2 ohms: 80 watts x 4 chan. | Bridged, 4 ohms: 160 watts x 2 chan.
Input sensitivity: Low level input: 200mV - 4V | High level input: 2.0mV - 10.0V
3-way protection circuitry (thermal, overload, and speaker short protection)
Fuse Rating: 40A x 1 inline (not supplied) | Dimensions: 7.68"W x 9.05"L x 2.09"H
Description
JL AUDIO JX400/4D 4-CHANNEL 400W RMS COMPONENT SPEAKERS TWEETERS AMPLIFIER NEW3. JL Audio JX1000/1D 1000 Watt RMS Monoblock Class D Car Amplifier with JL Audio RBC1 Remote Bass Control
Feature
AMPLIFIER: JX Series Monoblock Amplifier 500 rms @ 4ohms 750 rms @ 3ohms and 1000 rms @ 2ohmsUnregulated PWM switching type power supply, Variable Bass Boost (0 to +12 dB bass boost centered at 45 Hz), Soft start turn-on prevent clicking and popping when system turns on, Dimensions: 11"L x 7-3/4"W x 2"H
BASS CONTROL:JL Audio RBC1 Remote Bass Control, Remote Bass Control Works with Original Slash Series
JL Audio Amplifiers and the New V2 Slash, Remotely controls Bass EQ of JL Audio amplifiers, Low-profile design for custom installations, Overrides on-board boost control
CUSTOMIZATION: Choose your free Air Freshener. (Assorted Colors)
Description
JL Audio JX1000/1D 1000 Watt RMS Monoblock Class D Car Amplifiermono subwoofer amplifier- 500 watts RMS x 1 at 4 ohms (1,000 watts RMS x 1 at 2 ohms)
- Class D amplifier design
- MOSFET switching power supply
- frequency response: 20 Hz - 150 Hz
- variable low-pass filter (50-200 Hz, 12 dB/octave)
- variable bass boost (0-12 dB at 45 Hz)
- optionalwired remote level control
- preamp inputs and outputs
- speaker-level inputs
- 4-gauge power and ground leads and a 80-amp fuse recommended - wiring and hardware not included with amplifier
- no onboard fuses - when installing multiple amps in a system, an additional 80-amp in-line fuse between the distribution block and the amplifier is recommended
- 11-5/16"W x 2-1/8"H x 7-11/16"D
JL Audio RBC1
- remote bass control for JL Audio A-Series, G-Series, RD Series, and Slash v2 amplifiers (except the 300/2v2 and the 300/4v2)
- allows variable (0-12 dB) bass boost in JL Audio A-Series and G-Series amps
- remote level control for RD Series and mono JL Audio JX-Series amps (JX250.1, JX500.1, and JX1000.1)
- 18' remote cable and mounting hardware included
- 13/16"W x 13/16"H x 1-5/8"D
4. JL Audio RD1000/1 NexD Monoblock Class D Car Audio Amplifier
Feature
JL Audio RD-Series RD1000/1 | Class-D Monoblock Amplifier | RMS Power Rating: 4 ohms: 500 watts x 1 chan. | 2 ohms: 1000 watts x 1 chan. Total power output: 2000 watts | CEA-2006 Compliant AmplifierDifferential-Balanced Inputs | Speaker-level (high-level) inputs: JL Audio XD-CLRAIC2-SW Required, sold separately | NexDTM Technology delivers outstanding sound quality, efficiency and reliability | LED clipping indicators | Pulse Width Modulated MOSFET power supply
LED power (green) and protect (red) indicators | Soft start turn-on | Mono channel operation | Preamp RCA outputs to daisy chain multiple amps | 3-way protection circuitry (thermal, overload, and speaker short protection)
Dual speaker terminals simplify the hookup of multiple speakers | Heavy duty aluminum alloy heat-sink for extreme heat dissipation | Total Harmonic Distortion (THD): <1% | Variable low-pass filter: 50 - 500 Hz, 12 dB/octave | Low-Pass Slope (dB/octave): 12 dB/octave
Variable Bass Boost: 0 to +12 dB bass boost at 45 Hz | Fuse Rating: 80 A x 1 | Dimensions: 7"W x 14-11/16"L x 2-3/16"H
Description
JL AUDIO RD1000/1 MONOBLOCK 1000 WATTS RMS SUBWOOFERS SPEAKERS BASS CAR AMPLIFIER NEW5. JL Audio XD1000/1v2 Monoblock Class D 1000W Subwoofer Amplifier
Feature
Dimensions: 14 3/4"W x 7 1/8"L x 2"H4 gauge power and ground wiring is required for installation
Description
Monoblock Class D Subwoofer Amplifier RMS Power Rating: 2 ohms: 1000 watts x 1 chan. Mono channel operation One pair of pre-amp outputs Speaker-level RCV inputs Includes 2.5mm allen wrench for installation6. JL Audio XD700/5v2 5-channel car amplifier - 75 watts RMS x 4 at 4 ohms + 300 watts RMS x 1 at 2 ohms
Feature
5-channel car amplifer75 watts RMS x 4 + 180 watts RMS x 1 (at 4 ohms)
100 watts RMS x 4 + 300 watts RMS x 1 (at 2 ohms)
200 watts RMS x 2 bridged at 4 ohms + 300 watts RMS x 1 at 2 ohms
10-1/4"W x 2-1/16"H x 7-1/8"D
Description
General Features: XDv2 Series Class D 5-Channel Amplifier RMS Power Rating @14.4V: Channel 1 - 4 4 ohms: 75 watts x 4 chan. 2 ohms: 100 watts x 4 chan. Bridged 4 ohms: 200 watts x 2 chan. RMS Power Rating @14.4V: Sub Channel 4 ohms: 180 watts x 1 chan. 3 ohms: 240 watts x 1 chan. 2 ohms: 300 watts x 1 chan. RMS Power Rating @12.5V: Channel 1 - 4 4 ohms: 60 watts x 4 chan. 2 ohms: 90 watts x 4 chan. Bridged 4 ohms: 180 watts x 2 chan. RMS Power Rating @12.5V: Sub Channel 4 ohms: 180 watts x 1 chan. 3 ohms: 240 watts x 1 chan. 2 ohms: 300 watts x 1 chan. NexD High Speed Switching Class D Technology Wired HD-RLC remote level control available, sold separately LED power (green), over-current (yellow) and protect (red) indicators Advanced Rollback Protection Differential Balanced Input Section Selectable turn-on modes: REM / Offset / Signal +12 V Remote Turn-On: Traditional remote lead wire, from headunit DC Offset-Sensing: On/Off by detecting a very small DC signal (high-level signal only) Signal-Sensing: On/Off by detecting a full-range audio signal at left-channel input (high-level signal only) Speaker level inputs via RCA, JL Audio XD-CLRAIC2-SW required Heavy duty aluminum alloy heat-sink for extreme heat dissipation 3-way protection circuitry (thermal, overload, and speaker short protection) Detented, Calibrated Filter Freq. Potentiometer Input mode selectable: 2 Ch. / 4 Ch. / 6 Ch. State-variable / Sallen-Key Crossover Selectable Low-Pass Filter Slope (Sub Ch): 12 dB or 24 dB Variable low-pass filter: 50 - 500 Hz, 12 or 24 dB/octave Selectable HP filter mode (Ch 1/2): Off / x1 / x10 Selectable filter mode (Ch 3/4): Off / BP/ HP Input sensitivity: Low level: 800mV - 8V High level: 200mV - 2V Frequency Response (Ch 1-4): 12 - 22,000 Hz Frequency Response (Sub Ch): 10 - 1,000 Hz Total Harmonic Distortion (THD): <1% Signal to Noise Ratio: >104 dB Damping Factor @4ohms: >150 / 50 Hz Fuse Rating: 60A x 1 inline (not supplied)7. JL Audio RD-900/5 5-Channel 900 Watts RMS RD Series Class D Amplifier
Feature
JL Audio RD-Series RD900/5 | Class-D 5-Channel Amplifier | RMS Power Rating: 4 ohms: 75 watts x 4 chan. + 250 watts x 1 chan. | 2 ohms: 100 watts x 4 chan. + 500 watts x 1 chan. | 1 ohm: ------------N/A------------ | Total power output: 1800 wattsCEA-2006 Compliant Amplifier | NexDTM Technology delivers outstanding sound quality, efficiency and reliability | LED clipping indicators | Pulse Width Modulated MOSFET power supply | LED power (green) and protect (red) indicators
Soft start turn-on | Mono channel operation | Bridging switch for each channel pair | Preamp RCA outputs to daisy chain multiple amps | 3-way protection circuitry (thermal, overload, and speaker short protection) | Dual speaker terminals simplify the hookup of multiple speakers
Heavy duty aluminum alloy heat-sink for extreme heat dissipation | Total Harmonic Distortion (THD): <1% | Variable low-pass filter: 50 - 500 Hz, 12 dB/octave | Variable high-pass filter: 50 - 500 Hz, 12 dB/octave
Low-Pass Slope (dB/octave): 12 dB/octave | Variable Bass Boost: 0 to +12 dB bass boost at 45 Hz | Fuse Rating: 80 A x 1 | Dimensions: 7"W x 14-11/16"L x 2-3/16"H
Description
JL AUDIO RD900/5 5-CHANNEL 900W RMS COMPONENT SPEAKERS SUBWOOFERS AMPLIFIER NEW8. JL Audio RD400/4 NexD 4 Channel Class D Car Audio Amplifier
Feature
Power Handling:RMS @ 14.4 V: 75 watts x 4 @ 4 Ohm | 100 watts x 4 @ 2 Ohm | Bridged 200 watts x 2 @ 4 Ohm
RMS @ 12.5 V: 60 watts x 4 @ 4 Ohm | 90 watts x 4 @ 2 Ohm | Bridged 180 watts x 2 @ 4 Ohm
Frequency Response: 12 Hz - 22 Hz
Dimensions: 2.13 in / 54 mmb H x 9.78 in / 248 mm W x 6.96 in / 177 mm D
Description
4 Channel Class D Amplifier | CEA-2006 Compliant Amplifier | Differential-Balanced Inputs | NexD Technology delivers outstanding sound quality, efficiency and reliability | Preamp RCA outputs to daisy chain multiple amps | 3-way protection circuitry (thermal, overload, and speaker short protection) | Dual speaker terminals simplify the hookup of multiple speakers | Heavy duty aluminum alloy heat-sink for extreme heat dissipation9. JL Audio Slash Series 1200/1v3 Mono subwoofer Car Amplifier, 1,200 watts RMSx1
Feature
mono subwoofer amplifier1,200 watts RMS x 1 at 1.5 to 4 ohms
4-gauge power and ground leads and a 100-amp fuse recommended (Wiring and hardware not included with amplifier)
parametric EQ bass boost (0-15 dB at 20-80 Hz)
Class-D amplifier design
Description
1. mono subwoofer amplifier 2. 1,200 watts RMS x 1 at 1.5 to 4 ohms 3. Regulated, Intelligent Power Supply system 4. differential-balanced inputs 5. variable low-pass filter (40-200 Hz, 12 or 24 dB/octave) 6. parametric EQ bass boost (0-15 dB at 20-80 Hz) 7. variable infrasonic filter (15-60 Hz, 24 dB/octave) 8. optional wired remote bass boost 9. Class-D amplifier design 10. MOSFET power and output stages 11. preamp and speaker-level inputs (speaker-level input requires an optional adapter) 12. preamp outputs 13. 4-gauge power and ground leads and a 100-amp fuse recommended - wiring and hardware not included with amplifier 14. no onboard fuses - when installing multiple amps in a system, an additional 100-amp in-line fuse between the distribution block and the amplifier is recommended 15. 19-3/4"W x 2-7/16"H x 9-5/16"D10. RB XD400/4 JL AUDIO 4 CHANNEL AMP 400 W COMPONENT SPEAKERS TWEETERS AMPLIFIER
Feature
Description: 400W 2/3/4 Channel Amplifier | Inputs: Two Stereo Pairs | Speaker output connections: Accept up to 12 AWG wire | +12V and Ground connections: Accept up to 4 AWG wireRated Power 14.4 V Stereo: 75W RMS x 4 @ 4 ohms 100W RMS x 4 @ 2 ohms | Rated Power 14.4 V Bridged: 150W RMS x 2 @ 8 ohms 200W RMS x 2 @ 4 ohms | Rated Power 12.5 V Stereo: 60W RMS x 4 @ 4 ohms 90W RMS x 4 @ 2 ohms | Rated Power 12.5 V Bridged: 120W RMS x 2 @ 8 ohms 180W RMS x 2 @ 4 ohms
THD at Rated Power: <1% THD+Noise (20Hz - 20 kHz) | S/N Ratio: >104 dB referred to rated power (A-weighted, 20 Hz-20 kHz noise bandwidth) | >84 dB referred to 1W (A-weighted, 20 Hz-20 kHz noise bandwidth)
Frequency Response: 12 Hz - 22 kHz (+0, -1dB) | Damping Factor: >150 @ 4 ohms per ch./ 50 Hz | >75 @ 2 ohms per ch. / 50 Hz | Input Range: 100mV - 4V RMS | Dimensions (L x W x H): 8.52 in. x 7.09 in. x 2.05 in. | 217 mm x 180 mm x 52 mm
Recent Comments