Top 10 best reel roller boat trailer 2019
Finding the best reel roller boat trailer suitable for your needs isnt easy. With hundreds of choices can distract you. Knowing whats bad and whats good can be something of a minefield. In this article, weve done the hard work for you.
Best reel roller boat trailer
1. CE Smith Trailer Roller Guide-On- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat Trailer
Feature
1-1/2" Pre-galvanized steel uprights lean outward 15 Degree to cradle the boatGuide-ons are 21" tall above the frame with 9" roller & 2" roller caps at top & bottom
Mounting hardware included for frames up to 3" W x 4-1/4"H
Mounting brackets allow up to 13" of adjustment out from each side of the frame
Sold in pairs
Description
CE Smith Trailer, 27610, Roller Guide-On. These smooth rolling guides assist in centring the boat onto the trailer. Ideal for retrieving your boat on shallow ramps where the trailer is not far into the water, when you are alone, or have a crosswind or current pushing the boat.Uprights with rollers come fully assembled, ready for installation. For larger trailer frames check out our Large Frame U-Bolt Kit (11416). Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The edges of the pre-galvanized parts often lose their zinc coating during the stamping process. Because of the thinness of the coating less than 1 mm and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so its recommended that they be primed and painted.2. CE Smith Roller Bunk- Replacement Parts and Accessories for Your Ski Boat, Fishing Boat or Sailboat Trailer
Feature
Durable 2" polypropylene rollers on 1/2" shafts mounted in a heavy gauge pre-galvanized channelSupports up to 1500lbs of well distributed weight
Mounting hardwarenotincluded
5 rollers, 4 feet overall length
Description
Smith roller bunks make loading and unloading small craft at very short or even dry ramps easy. Great for ramps where it is not practical to float the boat onto the trailer. Fully factory assembled with durable 2 polypropylene rollers on shafts mounted in a heavy gauge pre-galvanized channel. Supports up to 1500 pounds of well distributed weight. May be installed using 10003GA mounting brackets as shown in the picture if lift and or angle is needed, or may be bolted directly to the trailer frame for a flat bottom boat, or even mounted on top of existing bunk boards. Mounting hardware is not included. Sold in pairs.3. CE Smith Trailer 29333 4"-1/2" ID Bell Assembly
Feature
Black thermal plastic rubber5-1/2 inch diameter
8 inches wide
1/2 inch shaft
Fits 4 inch wide center roller bracket
Description
CE Smith 29333, bell Assembly 4" - 1/2" ID - thermal plasticized rubber. 4" bow bell roller Assembly. Durable thermal plasticized rubber (TPR) bow bell assemblies help to center the boat and prevent bow to bow stand contact.4. CE Smith Trailer Post Guide-On with LED Lighted Posts, 60"- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat Trailer
Feature
Mounting hardware and wiring included; Sold in pairsAdjusts out to 19" each Side
Fits Frames up to 3" W x 4-1/4" H
1-1/2" square, 16 gauge pre-galvanized steel uprights 18" high
2-3/8" diameter white PVC posts
Description
CE Smith Trailer, 27760, 60" Post Guide-On with LED Lighted Posts. These Post Guide-Ons allow you to see the location of your trailer when it's under water. Equipped with long lasting, waterproof and shockproof, one piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. For larger trailer frames check out our Large Frame U-Bolt Kit (11416). Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The edges of the pre-galvanized parts often lose their zinc coating during the stamping process. Because of the thinness of the coating less than 1 mm and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so its recommended that they be primed and painted.5. CE Smith Y-Style Bow Stop, Yellow, 3-Inch- Replacement Parts and Accessories for your Ski Boat, Fishing Boat or Sailboat Trailer
Feature
Durable thermal plasticized rubber (TPR)5-3/4" span
3 inch square mount
Attaches firmly with 3/8 inch bolt
Description
This Y shape Bow stop is made from Durable thermal plasticized rubber (TPR). TPR is a strong, flexible, reusable, weather resistant and recyclable injection molded material that performs like natural rubber. TPR will not leave black marks, on your boat like black natural rubber. The stop acts as a bumper to keep your boat from hitting your trailer when loading the boat from the water It has the following dimensions:5-3/4" span across and has 3' x 3' mount for a secure fit.6. CE Smith Trailer 10401G Galvanized Roller Bracket Assembly, 5"
Feature
Use with 5 inch roller (Smith P/n 29515)Mount using 1/2" or 7/16" fasteners (not included)
Mounting slots are on 3 inch centers
5/8" diameter x 6-1/4" roller shaft (Smith P/n 10722a)
Panel bracket is Smith P/n 10301g40
Description
CE Smith 10401G, roller bracket Assembly, 5", galvanized. Panel brackets bolt to your trailer frame and typically brace a keel or spool roller to help with the transporting and loading of your boat. They are once piece made of strong 11-gauge hot dip galvanized steel. They have six gussets in the bends for added strength. Slots are 1/2" wide x 5" tall to provide plenty of adjustment to fit the hull. These assemblies some pre-assembled with a black rubber roller and roller shaft for easy installation. Made in the USA.7. CE Smith Trailer 10405G Galvanized Roller Bracket Assembly, 12"
Feature
Use with 12 inch roller (Smith P/n 29500)Mount using 1/2" or 7/16" fasteners (not included)
Mounting slots are on 10 inch centers
5/8" diameter x 13" roller shaft (Smith P/n 10727a)
Panel bracket is Smith P/n 10305g40
Description
CE Smith 10405G, roller bracket Assembly, 12" , galvanized. Panel brackets bolt to your trailer frame and typically brace a keel or spool roller to help with the transporting and loading of your boat. They are once piece made of strong 11-gauge hot dip galvanized steel. They have six gussets in the bends for added strength. Slots are 1/2" wide x 5" tall to provide plenty of adjustment to fit the hull. These assemblies some pre-assembled with a black rubber roller and roller shaft for easy installation. Made in the USA.8. CE Smith Trailer Post Guide-On with Unlighted Posts, 40"- Replacement Parts and Accessories for Your Ski Boat, Fishing Boat or Sailboat Trailer
Feature
Mounting Hardware included; Sold in PairsAdjusts out to 13" each Side
Fits Frames up to 3" W x 4-1/4" H 1-1/2" square, 16 gauge pre-galvanized steel uprights 18" high
2" schedule 40 white PVC posts (2-3/8" actual OD)
Description
CE Smith Trailer, 27620, 40" Post Guide-On with Unlighted Posts. These Post Guide-Ons allow you to see the location of your trailer when it's under water. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp. For larger trailer frames check out our Large Frame U-Bolt Kit (11416). Fits trailer frames up to 3" wide x 5-1/4" tall. Note: Check with your state Department of Transportation for restrictions regarding maximum trailer width. Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized. The edges of pre-galvanized parts often lose their zinc coating during the stamping process. Because of the thinness of the coating (less than 1 mm) and the fact that the edges remain exposed, pre-galvanized parts can begin to oxidize and rust quickly, so it's recommended that they be primed and painted.9. CE Smith Trailer 10403G Galvanized Roller Bracket Assembly, 8"
Feature
Use with 8 inch roller (Smith P/n 29502)Mount using 1/2" or 7/16" fasteners (not included)
Mounting slots are on 6 inch centers
5/8" diameter x 8-7/8" roller shaft (Smith P/n 10725a)
Panel bracket is Smith P/n 10303g40
Description
CE Smith 10403G, roller bracket Assembly, 8", galvanized. Panel brackets bolt to your trailer frame and typically brace a keel or spool roller to help with the transporting and loading of your boat. They are once piece made of strong 11-gauge hot dip galvanized steel. They have six gussets in the bends for added strength. Slots are 1/2" wide x 5" tall to provide plenty of adjustment to fit the hull. These assemblies some pre-assembled with a black rubber roller and roller shaft for easy installation. Made in the USA.10. CE Smith Trailer Bunk Board Guide-On, 5'- Replacement Parts and Accessories for Your Ski Boat, Fishing Boat or Sailboat Trailer
Feature
1-1/2" square pre-galvanized uprights, angled out at 75 Degree2'' x 4'' x 60" boards tilt to hug the hull and are covered with high grade marine carpet; Boards are untreated Southern Yellow Pine
Height of 21'' with adjustment out to 13" from frame on each side
Can be mounted on top of frame for extra height
Complete with mounting hardware to fit frames up to 3'' wide x 4-1/4'' high
Recent Comments