Top 10 best soldering braid 2019
Finding the best soldering braid suitable for your needs isnt easy. With hundreds of choices can distract you. Knowing whats bad and whats good can be something of a minefield. In this article, weve done the hard work for you.
Best soldering braid
1. MG Chemicals #3 No Clean Super Wick Desoldering Braid, 0.075" Width x 5' Length, Green
Feature
No clean super wickFlux residue is non-conductive and non-corrosive
Static free bobbins
Flux residue remaining on board does not have to be cleaned
High SIR-meets the requirements of both the bellcore specification TR-TSY-000078 and IPC test method III
NSF - Nonfood Compounds Program Listed P1, NSF Registration #154374
Description
No clean super wick. Flux residue is non-conductive and non-corrosive. Static free bobbins. Flux residue remaining on board does not have to be cleaned. High SIR-meets the requirements of both the bellcore specification TR-TSY-000078 and IPC test method III. ROHS Compliant.2. OMorc Desoldering Wick, Solder Sucker & Solder Braid (2.5mm Width, 1.5m Length) Desoldering Vacuum Pump Solder Removal Tool
Feature
Top-notch Quality. The solder sucker has an aluminum bronze frame and a high pressure vacuum which can remove solder from a printed circuit board effectively.Solder Wick Braid. The desoldering wick is 2.5mm wide and 1.5m in length. Weight: 0.4oz. With low residue design, this solder braid will help clean spare solder on the pin away to avoid short circuit, especially in small, hard to reach areas.
Pure oxygen free copper wire, no clean flux for easy to use. The solder wick can help clean some residue flux and BGA thermal bonding pad too.
Compact and Lightweight. Measuring 7.48''X0.79'', the desoldering pump can be used with only one hand, either your right or left hand.
Solid Construction. The solder sucker has plastic backing to ensure stability.
Description
Get the solder off and replace them with newer ones, which it is very common when soldering, so this solder sucker and solder wick will be your perfect companion to suck the solder away effectively.Suck the Solder Away Easily
The solder sucker measures 7.48"X0.79", which will fit your hands perfectly no matter if you are left-handed or right-handed. With metal body and high pressure vacuum, this desoldering pump can help you suck the solder away effectively.
Clean the Solder in Detail
2.5mm wide, 1.5m in length and 0.4oz in weight, the solder wick can clean the solder in some small or hard to reach areas. No clean flux, oxygen free copper wire. It will be a great accessory to remove the extra solder.
How to Use the Desoldering Pump
Step 1: Press the plunger down until it is been locked and you will hear a click;
Step 2: Make the tip of the soldering iron to the solder joint and allow the solder to become fully liquid;
Step 3: Move the tip of the pump next to the molten solder. Move the iron out of the way and immediately cover the liquid solder puddle with the pump's tip. Pull the trigger;
Step 4: Repeat this process if necessary.
How to Use the Solder Wick
Step 1: Place the wick over the solder you need remove and then just push the heated soldering iron tip onto the wick;
Step 2: Remove the wick once the solder has been absorbed;
Step 3: Cut off the used part of the wick;
Step 4: Repeat this process if needed
Why Choose Us:
All Our Products are Produced under Strict Quality Inspection
12-Month Worry-Free Warranty and Free Life-time Technical Support
Professional After-Sales Team
99% Positive Amazon Feedback
Package Included:
1* Solder Sucker
1* Solder Wick
Warranty:45 days money-back and 12-month, worry-free Guarantee!
3. Vastar Solder Wick, 3 Packs Desoldering Wick, Solder Braid 2.5mm Width, 1.5m (5ft) Length
Feature
High quality desoldering braidUnique no clean flux for easy to use
Pure oxygen free copper wire
Geometrically-precise weave
Size of the solder wick: Width 2.5mm, Length 1.5m, Weight 0.4oz
Description
Vastar desoldering wick is high quality desoldering braid with unique, no clean flux with a size of 0.10"W (2.5mm) x 5"L (1.5m), 0.4 oz. (11g).The solder wick can clean some small or hard to reach areas, which will be a great accessory to remove extra solder.
Package included:
3 x Vastar Desoldering Wick
Warranty:
18-month warranty. For any question, please feel free to contact us. We will get back to you within 24 hours.
4. Tabiger Solder Wick & Desoldering Pump, Solder Sucker & Desoldering Wick, 2pcs Solder Braid (2.5mm Width, 1.5m Length)- Desoldering Vacuum Pump Solder Remover
Feature
One-handed solder sucker with powerful suction Whether you are right or left-handed, you can using the desoldering pump by just cocking it and pressing the trigger button with one hand when you are ready, the desoldering pump designed with double ring double open and "vacuum" button, which make the sucking power awesome.Desoldering Wick with copper braid 2pcs solder braid with the size 2.5mm Width, 1.5m Length, this desoldering wick has geometrically-precise weave with copper and rosin, work from the tip of the desoldering wick, once the desoldering wick and the solder has been heated, the solder braid can quickly absorbed molten solder and left a clean working area.
ABS body with non-slip sponge and Nylon nozzle desoldering pump The body of the desoldering vacuum pump is made of high quality ABS, which make the solder sucker delicate and durable, also the covered sponge can absorb sweat and heat, make it comfortable to hold, the nylon nozzle of the solder suck can endure high temperature, thus it can be used for a long time.
3-in-1 Solder Removal Tool 1pcs desoldering vacuum pumps and 2pcs solder wicks, a must-have tool for electronics kit, the desoldering wick absorbs solder, the desoldering pump pulls it away quick, while the solder wick is better for small amounts of solder, the solder sucker takes up large amounts.
Widely used Solder Remover The Desoldering Wick & Desoldering Pump can be used to correct mistakes with small boards on PCBs, remove relays and other components from printed circuit boards, re-solder mechanical keyboard switches, unsoldering old wire from devices, desoldering computer parts such as a motherboard,clean alloy on smd components and more.
Description
TABIGER Solder Sucker & Solder WickIt's a must-have tool for electronics kit, you can use them togethersolder sucker for large amounts, while the solder wick used in small, hard to reach areas.
How to Use the Solder Sucker:
Step 1: Press the plunger down until you hear a click sound;
Step 2: Heat up solder around item to be removed by using a soldering iron;
Step 3: When the solder is liquid , place the tip of the solder sucker next to the liquid and press press the trigger;
Step 4: Repeat this process if necessary.
How to Use the Desoldering Wick:
Step 1: Place the wick over the solder you need to be removed and then just push the heated soldering iron tip onto the wick;
Step 2: Remove the wick once the solder has been absorbed;
Step 3: Cut off the used part of the wick;
Step 4: Repeat this process if needed.
Package Included:
1* Solder Sucker
2* Solder Wick
5. NTE Electronics SW02-10 No-Clean Solder Wick, 4 Blue.098" Width, 10' Length
Feature
Removes up to four times more solder than conventional wick, and extracts solder much faster than wicks based on Type-R fluxesResidue left behind is halide free and non-conductive, so it does not have to be cleaned off the board
100% copper wick has fine braid design to promote strong capillary action to pull in excess solder
Available with standard or anti-static bobbins
Description
NTE Solder Wick is made from fine copper wire woven together with a no-clean flux formula added to it to increase absorption.6. AUSTOR 1 Piece Desoldering Sucker and 6 Pieces Solder Braid Wick (2.0mm/2.5mm/3.0mm Width, 1.5m Length) with Flux - Desoldering Vacuum Pump Solder Removal Tool
Feature
High efficiency solder sucker - the desoldering pump designed with double ring and "vacuum" open button, you can remove solder from circuit board effectively by cocking it and pressing the trigger button with one handDesoldering braid wick with rosin - 6 pieces copper solder braid in 3 size, width 2.0mm/2.5mm/3.0mm, length 1.5m, 2 pieces for each size; geometrically-precise weave, can be used to clean the spare solder on the pin away to avoid short circuit, to meet your various of soldering needs
High quality material - the desoldering pump body made of premium quality ABS material, with non-slip sponge and nylon nozzle, anti-static, heat resistant and durable
Wide application - correcting mistakes on small PCB boards, removing relays and other components from printed circuit boards, cleaning small components, re-soldering and desoldering
7-in-1 solder removal tool - 1pcs solder sucker and 6pcs solder wicks in 3 size
Description
AUSTOR 7 Pieces Solder Sucker & Desoldering Wick kit, including 1 Piece Desoldering Sucker and 6 Pieces Solder Braid Solder Wick
Product instruction
How to Use the Solder Sucker
Product instruction
How to use the solder sucker
First: press down the plunger until it is locked with the sucker.
Second: heat up the solder until it become liquid.
Next: place the solder sucker near to the liquid,then press the button.
Last: repeat this process if needed.
Note
1. Don't take apart the nylon suction nozzle when you recive the desoldering sucker first time to prevent escapes.
2. Don't forget to put the black elastic back on the sucker after you pour the scruff out of it, then screw the nylon suction nozzle to ensure the sucker can be normal use.
3. If you find the double sping device no spring pressure when pressing the plunger, check whether the nylon suction nozzle had been screw tightly.
How to use the solder wick
First: place the wick over the solder which you want to remove.
Second: heat the wick and sold area by the soldering iron.
Next: remove the wick once the solder has been absorbed.
Last: cut off the wick you have used, repeat this process if needed.
Specifications
Desoldering Pump
Material: ABS
Length: 206mm
Diameter: 20mm
Solder Wick
Material: Copper with rosin
Wideth: 2.0mm/2.5mm/3.0mm
Length: 1.5m
Diameter: 55mm
Package include
1 * Desodering Pump
2 * Solder Wick 1.5M x 2.0mm
2 * Solder Wick 1.5M x 2.5mm
2 * Solder Wick 1.5M x 3.0mm
Product Warranty
All Austor products supply 45 days money-back & 18-month warranty. Any questions you have, please don't hesitate to contact us. We will get you back within 24hours.
7. CHEMTRONICS 80-3-5 BRAID, DESOLDERING, ROSIN SD, 5FT
Feature
Price For: Each Braid Material: Copper Width: 2mm Length: 5ft Braid Color: Green Braid Size: #3 Features: Packaged in ESD-Safe Static-Dissipative Bobbin Flux Type: Rosin Activated RA Leaded Process Compatible: Yes RoHS Compliant: YesDescription
Soder-Wick's pure copper braid has a unique geometric design that significantly reduces rework/repair time and minimizes the risk of heat damage to the board and sensitive components. Minimal flux residue on the board speeds up the cleaning process or eliminates it entirely.Braid Size: #3 Green
Braid Width: .080"
Braid Length: 5 ft.
Flux: Ultra high purity Type R rosin flux
Green .080 W x 5'L
8. Aven 17542 Desoldering Wick, 2.5mm Width, 5' Length
Feature
0.1"L x 5'LHigh quality desoldering braid
Unique no clean flux
Pure oxygen free copper wire
Description
Desoldering braid (wick) is a copper braid used in the rework and repair of printed circuit boards, computers, cell phones, or other electronics. Our desoldering wick is made from oxygen free copper, lets you easily remove the extra solder from components or pads on the circuit board. Just press the braid onto the connection with a hot iron and the solder wicks up into the braid.9. MG Chemicals Desoldering Braid #4 Fine Braid Super Wick with RMA Flux, 5' Length x 0.1" Width, Blue
Feature
Oxide-free clean copperStatic free bobbins
Only pure type 'RMA' rosin is used meeting the requirements of MIL-F-14256F (ANSI/J-STD-0004)
Manufactured under SPC guidelines
Designed to leave a residue that is environmentally safe
NSF - Nonfood Compounds Program Listed P1, NSF Registration #144207
Description
Any place you can put solder in, you can take it out with Super Wick. Remove the most expensive circuitry with confidence. Just lay the Super Wick on the soldered joint, apply tip of soldering iron to top-side for one second, and lift iron and Super Wick together to leave a clean connection ready for component removal or replacing. Super Wick is pure copper, specially woven wound on a pocket size spool with pressurized periphery. ROHS Compliant.10. MG Chemicals Desoldering Braid #1 Fine Braid Super Wick with RMA Flux, 5' Length x 0.025" Width , White
Feature
Oxide-free clean copperStatic free bobbins
Only pure type 'RMA' rosin is used meeting the requirements of MIL-F-14256F (ANSI/J-STD-0004)
Manufactured under SPC guidelines
Designed to leave a residue that is environmentally safe
NSF - Nonfood Compounds Program Listed P1, NSF Registration #144208
Recent Comments