Top 10 recommendation volt booster for 2019
When you looking for volt booster, you must consider not only the quality but also price and customer reviews. But among hundreds of product with different price range, choosing suitable volt booster is not an easy task. In this post, we show you how to find the right volt booster along with our top-rated reviews. Please check out our suggestions to find the best volt booster for you.
Best volt booster
1. Yosoo High Voltage Transformer DC 3v-6v to 400kV Boost Step-up Power Module High-voltage Generator 400000V
Feature
input voltage: DC 3 V to 6 VInput current: 2 A - 5 A
High pressure type: the type of pulse current
Output voltage: 400000 v(Please pay attention to safety)
High pressure discharge distance between: 10 mm - 20 mm.To avoid burning, use the time limit for 1 minute.
Description
Notice:
the high-voltage module should avoid the use of electricity in high voltage no-load . (Power must be adjusted to a suitable distance to the high-voltage output line , battery capacity is proportional to the distance and the use of the high-pressure arc ( not a voltage as high as possible , you must provide enough current ) . Experimental test of the arc distance from short to long , Do not exceed the maximum arc distance electricity, energy can not be released due to high pressure , can easily damage the module. )
Work: intermittent , continuous work does not allow more than 1 minute and the output side does not allow shorting . Improper voltage and long working hours easily damaged module
Package included:
1 * DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator
2. XCSOURCE DC 3.7V-7.4V to 1000kV Boost Step-up Power Module High-Voltage Generator 1,000,000V TE656
Feature
This high-voltage generator module is based on the principle of Tesla coil.This small high efficiency module can release high-voltage pulse output with simple external circuit power supply.
Ideal for students to study electrical experiment, do science experiment, etc.
Input: 3.7V - 7.4V / 4A
Output Voltage: 800KV - 1000KV
Description
Features:This high-voltage generator module is based on the principle of Tesla coil.
This small high efficiency module can release high-voltage pulse output with simple external circuit power supply.
Ideal for students to study electrical experiment, do science experiment, etc.
Specifications:
Model: MC-901
Dimension: 88.5 x 26mm (LxD)
Input Voltage: DC 3.7V - 7.4V
Input Current: 4A
Input Wire Length: 10cm (RED & Green/White Wire)
Output Voltage: 800KV - 1000KV (Please be careful when using)
Output Current: 0.5A
Output Wire Length: 16cm
Discharge Time: 10s
Arc distance/High voltage discharge distance range: 15mm - 20mm
Power supply: 1x 3.7V Lithium Battery, 2x 3.7V Lithium Batteries in series(such as 18650 Battery), NiCd/NiMH Batteries, 4V/6V Lead-acid Batteries, etc. (6V battery is Recommended for the best effect)
Input Wiring:
Red - Positive
Green/White - Negative
Notes:
1. The high-voltage module should not be powered on when it is under high voltage no-load status. (Power must be adjusted to a suitable distance to the high-voltage output line, battery capacity and voltage is proportional to the high voltage arc distance)
2.During the experiment, please test the arc distance from short to long, DO NOT exceed the maximum arc distance, or the high voltage energy might not be released and it may easily damage the module.
3. The input voltage will affect the output voltage and Arc distance.
4. The power of the module is large and the heat dissipation inside is weak. Please let the module work intermittently, continuous work no longer than 1 minute. Improper voltage and long working hours may easily damaged the module.
Package Includes:
1 x 3.7V to 1000KV Step-up Power Module Generator
3. Icstation MT3608 Mico USB DC Voltage Regulator, Step Up Boost Converter, Power Supply Module, 2V-24V to 5V-28V 2A (Pack of 4)
Feature
Mini DC-DC voltage converter board with micro USB voltage input,just connected with USB power adapter then you can get 9V 12V 18V 24V voltgeDC 2-24V input and 5V-28V adjustable voltage output with high power conversion efficiency up to 93%
Peak current: 2A (1A is recommended for a long time), Board Size: 30 X 17 X 14mm/1.18 X 0.67 X 0.55inch(L*W*H)
This is a boost converter module, so the output voltage should be at least 2V higher than the input voltage. When receive the voltage booster module, please turn the potentiometer clockwise by more than 10 turns before test, for example, rotate the potentiometer with 15 laps in clockwise direction, before power on it.
Fulfilled by Amazon usually spend 2-4 days to delivery, and fulfilled by seller usually delivery in around 17 days, with tracking information.
Description
ICstation mini DC-DC voltage booster module supporting DC 2V-24V input and DC 5V-28V adjustable voltage ouput with high conversion efficiency up to 93%. On-board micro USB power input port, just connected with the common USB power adapter then you can get 9V/12V/15V/18V/24V voltage ideal for DIY power supply.Specifications:
Input Voltage: DC 2V-24V
Output Voltage: DC 5V-28V
Peak Current: 2A
Maximum Coversion Efficiency: 93%
Maximum Load Power: 7W
Board Size: 30 X 17 X 14mm/1.18 X 0.67 X 0.55inch(L*W*H)
Packing:
1X Micro USB DC Voltage Regulator Board 2V-24V to 5V-28V
----------------------------- Warm Prompt -----------------------------
1. This is a boost converter module, so the output voltage should be at least 2V higher than the input voltage.
2. When receive the module, please turn the potentiometer clockwise by more than 10 turns before test, for example, rotate the potentiometer with 15 laps in clockwise direction, before power on it.
3. Peak current: 2A (1A is recommended for a long time). Cannot select the maximum value of voltage and current as the output at the same time. When the output voltage is increased, the output current is reduced accordingly, and vice versa.
4. Please send us an email in case you met problem in using or received defective one, we will take charge of your order and follow up your emails in 12 hours. Thank you!
4. DC Boost Step Up Power Module High Voltage Generator DC 3v-6v To 20kV
Feature
input voltage: DC 3 V to 6 VInput current: 2 A- 5 A
High pressure type: the type of pulse current
Output voltage: 400000 v(Please pay attention to safety)
ship by ePacket with tracking number, take 7-17 days. track in the usps
Description
Description:input voltage: DC 3 V to 6 V
Input current: 2 A- 5 A
High pressure type: the type of pulse current
Output voltage: 400000 v(Please pay attention to safety)
High pressure discharge distance between: 10 mm - 20 mm
The output high voltage wire length: 100 mm
Input power cord length: 100 mm (the red line is positive)
Wiring:
Red and green power connection red line:"+" green line "-"
output : the other side ,same color cable
lease notice:
the high-voltage module should avoid the use of electricity in high voltage no-load . (Power must be adjusted to a suitable distance to the high-voltage output line , battery capacity is proportional to the distance and the use of the high-pressure arc ( not a voltage as high as possible , you must provide enough current ) . Experimental test of the arc distance from short to long , Do not exceed the maximum arc distance electricity, energy can not be released due to high pressure , can easily damage the module. )
Work: intermittent , continuous work does not allow more than 1 minute and the output side does not allow shorting . Improper voltage and long working hours easily damaged module
Package includes:
1 * DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator
5. FASTROHY DC 3v-6v to 400kV Boost Step-up Power Module High-Voltage Generator 400000V
Feature
Two sections of small capacity lithium series of 7.2V, measured arc voltage has dropped to about 4V state,the capacity of the smaller voltage pulled lower. It is recommended to use more than one lithium battery 2000mA,4000mA best conditions with more batteryDetermine whether the battery capacity can be driven approach is the maximum power output of the battery when the voltage measurement arcing.If so you can 6V maximum power output Due to power,the internal heat is not easy,every power-on time should be controlled within a minute.
This module is a small production with high-pressure science inverter transformer/booster finished module,the input terminal DC3V-7.2V voltage can get 200,000 volts DC high voltage ( about 1-2 cm arc) at the output can be used as high school science experiments,electronic equipment, negative ion generator, high voltage source to use when making small science.
Voltage:Input DC3.6-6V,output DC400kV-600KV (Please note that when security);The high-voltage module uses the principle Tesla coil is made of high-voltage pulse output voltage;Commonly used in 105 high-voltage generator,high voltage ignition,teaching experiments
3.7V Li-ion battery can be used single or two series,such as 18650,idle cell phone batteries (to remove the protection board,the proposed capacity of 2000mAh or more) or NiCd/NiMH;Dimensions:24 * 65mm;Red and green power connection red line:"+" green line "-"
Description
Features:The high-voltage module uses the principle Tesla coil is made of high-voltage pulse output voltage
current,small size,high efficiency,simple external circuit (just plug in the switch,the battery can be )
discharge intensity violent.
Specification:
Voltage:Input DC3.6-6V, output DC400kV - 600KV ( Please note that when security )
High Type:Pulse Current
High voltage bipolar discharge distance:10mm-20mm
Output voltage lines Length:about 100mm
Input power cable length:about 100mm Input wiring:
Red and green power connection red line:"+" green line "-"
About Power:
Note:
Avoid high-pressure high-voltage module load electricity useMust adjust the high voltage side suitable distance ( before electricity, battery voltage and capacity is proportional to the distance from high-voltage arcing used when testing the arc distance from short to long experimen,prohibited from beyond the arc when powered up,the energy can not be released due to high pressure,easily damage the module. )
Determine whether the battery capacity can be driven approach is the maximum power output of the battery when the voltage measurement arcing.If so you can 6V maximum power output .
Two sections of small capacity lithium series of 7.2V, measured arc voltage has dropped to about 4V state,the capacity of the smaller voltage pulled lower.It is recommended to use more than one lithium battery 2000mA,4000mA best conditions with more battery .
Uses:
Commonly used in 105 high-voltage generator, high voltage ignition,teaching experiments
Package includes:
1 x 3v-6v to 400kV Boost Step-up Power Module
6. Vipe DC 3.6V-6V 400KV Boost Step-up Power Module Voltage Generator Black
Feature
This module is a small production with high-pressure science inverter transformer / booster finished module , the input terminal DC3V-7.2V voltage can get 200,000 volts for DC high voltage ( about 1-2cm arc ) at the output can be used as high school science experiments , electronic equipment, negative ion generator, high voltage source to use when making small science .Uses: Commonly used in 105 high-voltage generator, high voltage ignition, teaching experiments
Due to power, the internal heat is not easy , every power-on time should be controlled within a minute
Determine whether the battery capacity can be driven approach is the maximum power output of the battery when the voltage measurement arcing . If so you can 6V maximum power output
Two sections of small capacity lithium series of 7.2V, measured arc voltage has dropped to about 4V state , the capacity of the smaller voltage pulled lower. It is recommended to use more than one lithium battery 2000mA , 4000mA best conditions with more battery
Description
Specification:
Voltage: Input DC3.6-6V, output DC400kV - 600KV( Please note that when security )
High Type: Pulse Current
High voltage bipolar discharge distance: 10mm-20mm
Output voltage lines Length: about 100mm
Input power cable length: about 10mm (red is positive)
Dimensions: 24 * 63mm
About Power:
3.7V Li-ion battery can be used single or two series, such as 18650 , idle cell phone batteries ( to remove the for protection board , the proposed capacity of 2000mAh or more ) or NiCd / NiMH battery pack , 4V or 6V Lead Acid batteries.
This module is a small production with high-pressure science inverter transformer / booster finished module , the input terminal DC3V-7.2V voltage can get 200,000 volts for DC high voltage ( about 1-2cm arc ) at the output can be used as high school science experiments , electronic equipment, negative ion generator, high voltage source to use when making small science .
Note:
Avoid high-pressure high-voltage module load electricity use. Must adjust the high voltage side suitable distance ( before electricity, battery voltage and capacity is proportional to the distance from high-voltage arcing used when testing the arc distance from short to long experiment , prohibited from beyond the arc when powered up , the energy cant be released due to high pressure , easily damage the module. )
Due to power, the internal heat is not easy, every power-on time should be controlled within a minute.
Package included:
1x 3v-6v to 400kV Boost Step-up Power Module
7. Qianson High Voltage DC-DC Boost Converter 8V-32V to 45V-390V Adjustable ZVS Capacitor Charging Power Supply Module
Feature
Input voltage: two input voltage range selectable, (jumper selectable through the back of the PCB, default setting 10-32V input): 1) 8V-16V input 2) 10V-32V inputInput Current: 5A (MAX)
Output voltage: 45-390V continuously adjustable (the default output 50V. This module has regulator function, after adjusted output voltage is stable and unchanging, not with changes in input voltage changes)
Output Current: 0.2A MAX (affected by input voltage and dropout voltage,the higher the output voltage, the smaller the output current)
Output Power: 40W (peak 70W)
Description
Name: High Voltage boost converter module
Properties: non-isolated step-up module
Input voltage: two input voltage range selectable, (jumper selectable through the back of the PCB, default setting 10-32V input)
1, 8V-16V input
2, 10V-32V input
Input Current: 5A (MAX)
Quiescent current: 15mA (12V step up to 50V, the higher the output voltage will increase the quiescent current)
Output voltage: 45-390V continuously adjustable (the default output 50V. This module has regulator function, after adjusted output voltage is stable and unchanging, not with changes in input voltage changes)
Output Current: 0.2A MAX
Output Power: 40W (peak 70W)
Working temperature: -40 ~ + 85
Operating frequency: 75KHz
Conversion efficiency: up to 88%
Short circuit protection: Yes. (Input 10A fuse, at the output please do not short circuit arc, it may damage component, if you need please add power resistor in series for limiting)
Overcurrent protection: Yes. (Input current exceeds 4.5A, reducing the output voltage)
Overvoltage protection: Yes (Output voltage exceeds 410V, lowering the output voltage) Input reverse polarity protection: Yes (non-self-healing, reverse burning fuse, you have better not reverse it.)
Dimensions: 60(L)*50(W)*22(H)mm
The capacitor charging time measured data:
470uF full charge to 390V time is 2 seconds
1000uF full charge to 390V time is 4 seconds
2200uF full charge to 390V time is 8 seconds
4700uF full charge to 390V time is 18 seconds
Warning! The module output is high voltage, on people, animals have life-threatening, the course please pay attention to safety precautions. We are not responsible.
Package list:
1 x DC Boost Converter 45-390V Output
8. Gowoops 2PCS 150W DC-DC 10-32V to 12-35V Step Up Boost Converter Module Adjustable Power Voltage
Feature
Convenient for DIY -- You can use this module to DIY an output-adjustable car power supplyInput voltage: DC 10V-32V, Output voltage: DC12V-35V(adjustable)
Input current: 16A (MAX), Output current: 10A (MAX)
Conversion efficiency: 94% (For reference: when Input 19V 2.5A Output 16V)
Easily charging for 60W, 90W etc. laptops which is less than 150W, industrial grade ( -40 degree to + 80 degree) work temperature, suitable for AC adapter, power supply and so on
Description
Featrure:
Easy to drive 65W 90W dual-core notebook. Use a 12V battery drive 19V 3.42A notebook, the module temperature about 45
Conversion efficiency: 94% (For reference: when Input 19V 2.5A Output 16V)
Output Ripple: 2% (MAX) 20M-bandwidth
Operating Temperature: Industrial (-40 to +85) (ambient temperature exceeds 40c, lower power use, or to enhance heat dissipation)
Full load temperature rise: 45
No-load current: 25mA typical
Voltage regulation: 0.5%
Dynamic response speed: 5% 200uS
Short circuit protection: None (Please Install fuses and protection circuits at Input port.)
Input Reverse Polarity Protection: None (please comply with a reverse protection or connect a diode at input parts)
Specifiction:
Input voltage: DC 10V-32V
Output voltage: DC12V-35V(adjustable)
Input Current: 16A (MAX) (Please enhance heat dissipation if more than 10A)
Output Current: 10A (MAX)
Output power: natural cooling 100W (MAX), strengthening cooling 150W (MAX) real power
Module Properties: non-isolated step-up module (BOOST)
Size: 65mm x 35mm x 21mm
Package Includes:
2 x 150W Boost Converter
9. RioRand 5 Pack Boost Converter Module XL6009 DC 3.0-30 V to DC 5-35 V Output Voltage Adjustable Step up Circuit Board 4A
Feature
XL6009 is a high-performance 400KHz 4A switch currency step-up (BOOST) module. This module is coming with the 3rd generation high-frequency switch technology as the core chip, The performance is much higher than LM2577Wide input voltage: 3V~32V;Optimum operating voltage range: 5~32V;Wide output voltage: 5V~35V
With 4A high efficiency MOSFET switches, the efficiency of XL6009 can be up to 94%(LM2577current is 3A)
With ultra high switch frequency 400KHz , even if small capacity filtering capacitors can achieve very good results, ripple is smaller (Compared to LM2577,its frequency is 50KHz)
Package Content : 5*DC-DC Step Up Boost Module
Description
Attention: Do not plug this booster to your project before adjusting the potentiometer Technical Parameters: Model: XL6009 boost module Module Properties: Non-isolated boost (BOOST) Rectification: Non-Synchronous Rectification Input Range: 3V ~ 32V Output Range: 5V ~ 35V Input Current: 4A (max), no-load 18mA (5V input, 8V output, no-load is less than 18mA. Higher the voltage, the greater the load current.) Conversion efficiency: less than 94% (greater the pressure, the lower the efficiency) Switching frequency: 400KHz Output Ripple: 50mV (the higher the voltage, the greater the current, the greater the ripple) Load Regulation: +/-0.5% Voltage Regulation: +/-0.5% Operating Temperature: -40 degree to +85 degree (strengthen heat dissipation while ambient temperature exceeds 40 degrees) Body Size: 4.3 x 2.1 x 1.2cm/1.7" x 0.8" x 0.47"(L*W*T) Net Weight for 1 pc: about 10g Input way: IN+, IN- Output way: OUT+, OUT- Test Comparison Sample Reference: Input 3V Output 12V 0.4A 4.8W Input 5V Output 12V 0.8A 9.6W Input 7.4V Output 12V 1.5A 18W Input 12V Output 15V 2A 30W Input 12V Output 16V 2A 32W Input 12V Output 18V 1.6A 28.8W Input 12V Output 19V 1.5A 28.5W Input 12V Output 24V 1 A 24W Vin * Iin * Efficiency = Vout * Iout Vin: Input Voltage Iin: input current Vout: Output Voltage Iout: output current Package Content : 5*RioRand DC-DC Step Up Boost Module10. Boost Voltage Converter, DROK 1500W Voltage Regulator Booster DC 10V-60V 12V Step Up to DC 12V-90V 24V 30A Power Supply Module High Power Volt Transformer Circuit Board with Cooling Fan
Feature
DROK boost voltage converter input voltage range is DC 10-60V, continuously adjustable output voltage range is DC 12-90V, max output current is 20A, more than 15A please enhance heat dissipation.Application: DIY a power supply, 12V can input and output can 12-50V adjustable; as the car power supply, charge for your laptop, PDA or a variety of digital products; Solar panel regulator etc.
Protection: the step-up power regulator is designed with input over-current protection, battery low voltage protection, input MOS reverse polarity protection, short circuit protection.
Speacial Design: the voltage transformer is equipped with thickening radiator and intelligent temperature control cooling fan.
Note: it is necessary to lower the battery protection voltage, no matter using the battery, switching power supply, solar panel, or generator etc as the input source, otherwise it will damage the battery and power module.
Description
DROK 1500W Boost Voltage Converter
Parameters:
Module type: non-isolated step-up module (BOOST)
Input voltage range: DC 10V~60V
Input current: 10~30V input voltage, maximum current 30A; 31~60V input voltage, maximum current 25A
Static operating current: 15 mA (when 12V step up to 20V, the higher the output voltage, the current will increase)
Output voltage: 12~90V continuously adjustable (default 19V)
Output current: 20A MAX, more than 15A please enhance heat dissipation
Constant current range: 0.8~20A (0.3A)
Temperature: -40~ + 85(if the ambient temperature is too high, please enhance heat dissipation)
Operating frequency: 150 KHz
Conversion efficiency: 92% ~ 97%
Protection: input over-current protection, battery low voltage protection, input reverse polarity protection, short circuit protection
Installation: 4 x 3 mm screw holes
Module size(L*W*H): 130 x 52 x 85 mm
Applications:
1. DIY a power supply, input 12V and output can be adjustable to 12-50V.
2. Charge for your electromobile.
3. As the car power supply, charge for your laptop, PDA or a variety of digital products.
4. DIY a notebook mobile power supply: with 12V big-capacity lithium battery pack, get your notebook on anywhere.
5. Solar panel regulator.
Package Including:
1 x Power Converter Module
Recent Comments