Top betafpv dsmx for 2019
If you looking for betafpv dsmx then you are right place. We are searching for the best betafpv dsmx on the market and analyze these products to provide you the best choice.
Best betafpv dsmx
1. BETAFPV BetaCube F4 FC Frsky Receiver OSD Smart Audio Z02 FPV AIO 5.8G VTX Camera with Cam Mount for Tiny Whoop Quads Beta75S Beta65S
Feature
There are two update points in this newest version Betacube: Z02 FPV camera is upgraded to wire connection way; Added a 25 white camera mount in this cube. Improved flexibility and enhanced the camera's security. You can just plug and play.Binding Procedure--Easier than usual, No need to click the bind button when power on: https://betafpv.freshdesk.com/support/solutions/articles/27000021366-how-to-bind-your-radio-transmitter-brushed-fc-board
F411 Processor can reach to 100MHz, much faster than the F3 Flight Controller with 72Mhz. Integrated with Frsky receiver only. With this plastic holder you can use it on all the 1S brushed and brushless whoop drone.
The Z02 FPV Camera has wide lens angle of 100 to 120 Degrees with 1/4 lens. Support touch switch select channel Frequency group. Output power of the transmitter is adjustable 25mW to 200mW with the voltage of 2.9V- 5.5V.
Some basic guidance and typical FAQ, please check it here : https://betafpv.freshdesk.com/support/solutions
Description
BETAFPV BetaCube F4 FC Frsky Rx Z02 AIO 5.8G VTX Camera Smart Audio for Tiny Whoop Quads Like Beta75S BNF
This is the upgraded version of Betacube. A customed plastic holder is made in this newest version. Soldering is done ahead of time you can use it when received. F4 FC+OSD+ Frsky Rx flight controller with AIO 5.8g newest Z02 VTX camera.
Specification:
CPU: STM32F411CEU6
Six-Axis: MPU6000
ESC: All FETs are rated at 30A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors.
Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Betaflight MATEKF411RX 3.4.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: SPI Frsky D16 protocol (AKA FRSKY_D on Betaflight Configuration)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Output power: 0mW, 25mW and 200mW (Adjustable)
Supply Voltage: 2.9-5.5V
Size : 27*17*14 mm
Weight: 4.7g
Antenna: Omnidirectional ANT
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
TV System: NTSC
Field of view: 100-120 degrees with 1/4 lens.
Packagge Included:
1 * BETAFPV F4 brushed flight controller (all connectors soldered)
1 * BETAFPV Z02 AIO camera VTX (all connectors soldered)
1 * 25 Z02 Camera Amount
4 * M1.24mm screws (fit for stock Inductrix frame)
4 * M1.45mm screws (fit for Beta75 etc 75mm frame)
4 * Amti-vibration ruber dampers
2. BETAFPVBeta75X2SBrushlessWhoopDronewith2SF4FCDSMXZ02CameraOSDSmartAudio11000KV1103MotorXT30CableforTinyWhoopFPVRacing
Feature
Please note: In the Beta75X BNF setup, when you connect the receiver to 2S FC, don't forget to plug the battery, otherwise the receiver will have no power to work at all.The DSMX receiver used on the 75X is different from the one we used before. The binding procedure is also different. Check out the details on the support link below. http://support.betafpv.com/support/solutions/articles/27000051188-cli-dump-of-beta65x-and-beta75x-dsmx-version.
The Beta75X drone comes with "props out" in default. With reversed props or "props out", so no more dipping even in hardest cornering. More details please check https://betafpv.freshdesk.com/support/solutions/articles/27000050781-know-more-about-props-out-
Durable and light enough frame is customed for the Beta65X. A total weight of 26g give pilots a good balance of weight and nice punch on HV battery. 2pcs 1S 260mAh Lipo HV batteries are recommended in default. So pilot could also use their whoop batteries.
Whole drone no soldering or tinkering necessary. Customed lightest 0802 17500KV motors with cable connectors. Just plug and play. And the camera is the Z02 AIO VTX, spilt and 35 camera mount for more fast flying, smart audio and output power switchable is also available for VTX remote control.
Description
BETAFPV Beta75X 2S Brushless Whoop Quadcopter DSMX OSD Smartaudio with 1103 11000KV Motor XT30 Cable for FPV Racing Whoop
Here is a introducing video shared by Nate Payne:
https://www.youtube.com/watch?v=JHH17wrMbg0&feature=youtu.be
SPECIFICATION
Weight: 41g (without battery)
Motors: 1103 11000KV with connector
Props: 40mm 4-blades props, 1.5mm shaft hole
Recommend battery: 300mAh 2S battery
Receiver Option: DSMX
FC
CPU: STM32F405
Six-Axis: MPU6000
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD) 3.5.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Smart Audio port is available for radio control VTX
ESC
Support BLheli/BLHELI_S suite Pass-through ready
Dshot600 in default
Input voltage: 2S lipo
Cotinue current: 6A
Peak current: 10A
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G
Z02 AIO Camera VTX -- On the Beta75X, it is the customed version with VTX board and camera board split.
Smart Audio function is included for radio control
Output power: 0mW, 25mW and 200mW (Adjustable)
Antenna: Dipole ANT
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
TV System: NTSC
Field of view: 100-120 degrees with 1/4 lens
Recommend Part:
2S Brushless FC:www.amazon.com/dp/B07H8XQ7R6
300mAh 2S Battery:www.amazon.com/dp/B07H8G5ZPW
1103 Motor:www.amazon.com/dp/B07FN64599
Z02 Cam:www.amazon.com/dp/B07FNRLFGZ
Beta75X Frame Kit: www.amazon.com/dp/B07GYJP8HF
40mm Prop: www.amazon.com/dp/B07H9B2GJH
Package:
1 * Beta75X DSMX BNF 2S Whoop Quadcopter
1 * 300mAh 2S 35C-75C battery
1 * Spare 40mm 4-blades props (2CW+2CCW)
1 * Spare Canopy
3. BETAFPV F4 FC 1S Brushed Flight Controller DSMX Receiver ESC OSD Smart Audio for Tiny Whoop FPV Micro Racing Drone
Feature
BETAFPV F4 FC 1S Brushed Flight Controller Integrated DSMX receiver and OSD. NOT compatible with Spektrum DXe radio transmitter and OrangeRX RF module. For some Spektrum radio transmitter like DX6i/DX6e etc, the DSMX receiver may have a horrible range with your radio transmitter, please change the mode to DSM2 (DSMX in default).The binding procedure is different from before, there is no bind button on it, just set in betaflight and then power on, more details checking here: https://betafpv.freshdesk.com/support/solutions/articles/27000021366-how-to-bind-your-radio-transmitter-brushed-fc-board
The F4 brushed FC board bring a new era in FPV whoop technology. Improved on 3 points: STM32F411 100MHz high performance MCU, 30A lower resistance MOSFETs and polar reversed protection. All of these is backed by the same reliability and warranty of all BETAFPV FC boards.
Fully programmable through Betaflight, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings.
The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector.
Description
BETAFPV F4 FC 1S Brushed Flight Controller DSMX Receiver ESC OSD Smart Audio for Tiny Whoop FPV Micro Racing Drone
Please note the binding procedure is different from before, there is no bind button on it, just set in betaflight and then power on, turn on the radio and select bind mode, more details checking here:
https://betafpv.freshdesk.com/support/solutions/articles/27000021366-how-to-bind-your-radio-transmitter-brushed-fc-board
Specification
CPU: STM32F411CEU6
Six-Axis: MPU6000
ESC: All FETs are rated at 30A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors.
Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Betaflight MATEKF411RX 3.5.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: DSM2/DSMX (DSMX in default)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 3.8g
Package:
1 * F4 DSMX Brushed FC ( 55mm PH-JST 2.0 power cable soldered)
4 * M1.2x4mm screws (Fit for stock Inductrix frame)
4 * M1.4x5mm screws (Fit for Beta75 etc 75mm frame)
4 * Anti-vibration ruber dampers
1 * 55mm PH-JST 1.25 power cable pigtail
4. BETAFPV Beta75S Whoop Drone 1S Brushed FPV Quadcopter with F4 FC DSMX Receiver Z02 Camera OSD Smart Audio 8X20 Motor for Tiny Whoop FPV Racing
Feature
Beta75S is upgraded to F4 Brushed FC (DSMX RX) with Z02 Wire Connected Camera (with 25 camera mount).The binding procedure is different from before, there is no bind button on FC, just set in betaflight and then power on, more details checking here: https://betafpv.freshdesk.com/support/solutions/articles/27000021366-how-to-bind-your-radio-transmitter-brushed-fc-board
The Beta75S has 2 improvement based on Beta75 drones: 1.Motors: 7x20mm -> 8x20mm brushed motors. 2.Battery: 260mAh -> 550mAh Lipo HV battery
Great alternative to popular Tiny Whoop quadcopter. More punch on throttle with 8x20mm 14000KV motors and 3-blade 40mm propellers.
The same hole pattern with Tiny Whoop flight controller.
Description
BETAFPV Beta75S Whoop Drone 1S Brushed FPV Quadcopter with F4 FC DSMX Receiver Z02 Camera OSD Smart Audio 8X20 Motor for Tiny Whoop FPV Racing
Specifications:
Wheelbase: 75mm
Weight: 38g (without battery)
Flight Controller: BETAFPV F4 Brushed FC(DSMX RX)with OSD
Firmware Version: Betaflight BETAFLIGHTF3 3.2.0
Motor: 8x20mm 15000KV brushed motor
Receiver: DSM2/DSMX (DSMX in default)
CameraZ02 Camera (with 25 camera mount).
Battery: 550mAh Lipo HV battery with PowerWhoop connector
Flight time: 5 min
Assembly Parts List:
Frame: Beta75S frame
Motors: 8x20mm brushed motors
Props: 40mm 3-blades props
FC: BETAFPV F4 brushed FC with OSD (According to different Rx version)
AIO camera: Z02 Camera
Battery: 550mAh LiHV battery
DSMX RX:
The DSMX version support DSM, DSMX protocal, can support Spectrum DXE, DX6, DX6E transmitter and so on.
Package Included:
1 * Beta75S Micro FPV Quad
1 * BETAFPV 550mAh 1S Lipo HV Battery
5. BETAFPVBeta65X2SBrushlessWhoopDronewith2SF4FCDSMX Z02CameraOSDSmartAudio17500KV0802MotorPH2.0CableforTinyWhoopFPVRacing
Feature
In the Beta65X BNF setup, when you connect the receiver to 2S FC, don't forget to plug the battery, otherwise the receiver will have no power to work at all.The DSMX receiver used on the 65X is different from the one we used before. The binding procedure is also different. Check out the details on the support link below. http://support.betafpv.com/support/solutions/articles/27000051188-cli-dump-of-beta65x-and-beta75x-dsmx-version.
The Beta65X drone comes with "props out" in default. With reversed props or "props out", so no more dipping even in hardest cornering. More details please check https://betafpv.freshdesk.com/support/solutions/articles/27000050781-know-more-about-props-out-
Durable and light enough frame is customed for the Beta65X. A total weight of 26g give pilots a good balance of weight and nice punch on HV battery. 2pcs 1S 300mAh Lipo HV batteries are recommended in default. So pilot could also use their whoop batteries.
Whole drone no soldering or tinkering necessary. Customed lightest 0802 17500KV motors with cable connectors. Just plug and play. And the camera is the Z02 AIO VTX, spilt and 35 camera mount for more fast flying, smart audio and output power switchable is also available for VTX remote control.
Description
BETAFPV Beta65X 2S Brushless Whoop Quadcopter Frsky OSD Smartaudio with 0802 17500KV Motors for FPV Racing Whoop
Here is a introducing video shared by Daniel Sugano:
https://www.youtube.com/watch?v=faen8NN5GcI&feature=youtu.be
SPECIFICATION
Weight: 26g (without battery)
Motors: 0802 17500KV with connector
Props: 31mm 4-blades props, 1.0mm shaft hole
Camera tilt angle: 35 degree
Receiver Option: Frsky XM / FullSpeed DSMX
Batteries: 300mAh 1S Lipo HV batteries
FC
CPU: STM32F405
Six-Axis: MPU6000
Size: 26mm x 26mm, whoop mounting pattern
Firmware version: Betaflight OMNIBUSF4SD (OBSD) 3.5.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Smart Audio port is available for radio control VTX
ESC
Support BLheli/BLHELI_S suite Pass-through ready
Dshot600 in default
Input voltage: 2S lipo
Cotinue current: 6A
Peak current: 10A
Firmware: BLHELI_S
Processor: SILABS EFM8BB21F16G
Z02 AIO Camera VTX -- On the Beta65X, it is the customed version with VTX board and camera board split.
Smart Audio function is included for radio control.
Output power: 0mW, 25mW and 200mW (Adjustable)
Antenna: Dipole ANT
Frequency: 5.8GHz 6 bands 48 channels, with Raceband: 5362~5945MHz
TV System: NTSC
Field of view: 100-120 degrees with 1/4 lens
Recommend Part:
2S Brushless FC: www.amazon.com/dp/B07H8XQ7R6
260mAh Battery: www.amazon.com/dp/B07121V7MB
0802 Motor: www.amazon.com/dp/B07GYR31T8
Z02 Cam: www.amazon.com/dp/B07FNRLFGZ
31mm Prop: www.amazon.com/dp/B07D7WSL3L
Package:
1 * Beta65X BNF 2S Whoop Quadcopter
2 * 300mAh 1S Lipo HV batteries
1 * Spare 31mm 4-blades props (2CW+2CCW)
1 * Spare Canopy
6. Makerfire Micro F3 Brushed Flight Controller FC (No Receiver) Betaflight OSD Cleanflight Compatible with PPM, SBUS, IBUS, Spektrum DSM2/DSMX,Frsky XM/XM+ for Tiny Whoop Blade Inductrix Quadcopter
Feature
The FC and OSD Programs are Integrated in one MCU, Without extra MCU to control the OSD, What's more, the OSD Assistant Software is also Integrated with the Flight Control. The Microcontroller Controls the OSD Chip through the SPI BUS DMS Mode, It will be much more Faster.Using MPU6000 Sensor and Connect it Via SPI bus,to Increase the Sample Rate of the Sensor, to Inrease the Running Frequency of MCU Master Program, to Provide Higher Control Precision and Faster Response Speed.
It is Compatible with theTiny Series Frame. The Flight Controller is Fixed by the Damping Ball, Which can Effectively Eliminate the Vibration Brought by the Tiny Series Motor and Improve the Stability of the Flight Control.
Betaflight/Cleanflight can be switched freely, and the OSD location and information can be configured directly in the Configurator.
Compatible Receivers Signal: PPM, SBUS, IBUS, Spektrum DSM2 / DSMX, Frsky XM/XM+,,flysky etc.
Description
Specification:Firmware: betaflight_3.3.3_OMNIBUS
CPU: STM32F303CCT6
Sensor: MPU6000
Compatible Receivers Signal: PPM, SBUS, IBUS, Spektrum DSM2 / DSMX, Frsky XM/XM+,,flysky etc.
Power supply: MAX 4.35V ,(1S) Battery
Current: 5A Continuous Peak 6A
Screw Hole Spacing: 30*30mm Diameter=3.5mm
External LED_STRIPGND 5V LED
OSD Interface: VIN VOUT 5V GND
Can be External 5V / 0.5A Step-up Circuit BEC
Micro USB Connector
Weight: 3.3g
Feature:
Mini F3 30*30mm is Suitable for all the Tiny Whoop and Micro RC Drones.
OSD Function can Help to Confirm the Location of the Flying Drones.
Compatible with all Popular Receivers like DSM,Frsky,flysky and Sbus etc.
Support DIY: External BEC, LED and Receiver.
Notice:
The Receiver Configuration, When Input the SBUS and DSM, Please Configure RX2 as Input Interface.
The DSM2/DSMX Receiver Output 3.3V,the SBUS and PPM Receivers Supply 5V.
Package Including
1 * Mini F3 Flight Controller+OSD (NO Receiver Version)
1 * Cable
4 * Rubber Rings
7. BETAFPV F4 FC 1S Brushless Flight Controller SPI Frsky Receiver ESC OSD Smart Audio for Tiny Whoop FPV Micro Racing Drone
Feature
The default configuration from factory is Frsky D16 mode (FRSKY_X). Built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules. In Betaflight Configuration, it should be setted as FRSKY_D receiver (aka Frsky D8 mode) or FRSKY_X receiver (aka Frsky D16 mode) in SPI RX mode.This is a SPI Frsky receiver. Binding easier than before, no need to click the bind button when power on. Manual: https://betafpv.freshdesk.com/support/solutions/articles/27000021366-how-to-bind-your-radio-transmitter-brushed-fc-board
F411 Processor can reach to 100MHz, much faster than the F3 Flight Controller with 72Mhz. Integrated with Frsky receiver only. You can click here to get the Cli Dump of Beta75pro with the FC: http://support.betafpv.com/support/solutions/articles/27000050395-cli-dump-of-f4-1s-brushless-flight-controller-frsky-version
Firmware version: betaflight_matekf411rx_3.4.0. Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode). Support Smart Audio.
Some basic guidance and typical FAQ, please check it here : https://betafpv.freshdesk.com/support/solutions
Description
BETAFPV F4 1S Brushless Flight Controller Frsky Receiver Integrated ESC OSD Smart Audio for FPV Micro Racing Drone
Binding Procedure--Easier than usual. No need to click the bind button when power on.
a.Power on the board, connecting the battery or USB power. Then the green receiver LED start to flash.
b.Press the bind button for 3s. Then the green receiver LED will be solid on. It means the receiver is in bind mode and you could start to bind your radio transmitter.
Checking here: https://betafpv.freshdesk.com/support/solutions/articles/27000021366-how-to-bind-your-radio-transmitter-brushed-fc-board
Specifiction
Firmware version: betaflight_matekf411rx_3.4.0
CPU: STM32F411CEU6 (100MHZ, 256K FLASH)
Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
Size: 26mm x 26mm, compatible with the Inductrix quad frame, Beta65 Pro frame, Beta75 Pro frame, Whoop B06 frame etc
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 4g
ESC
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125
Recommend Parts:
Frame: Beta65 Pro / Beta75 Pro frame
www.amazon.com/dp/B078GLW4HK
www.amazon.com/dp/B078H7R3PV
Props: 31mm 4-Blades / 40mm 4-blades propsMotors: 0703 / 0603 motors
www.amazon.com/dp/B079HXLJJ5
www.amazon.com/dp/B078N93QVP
Battery: 550mAh 1S batteries
www.amazon.com/dp/B078WR2FVR
Package List:
1 * F4 1S brushless flight controller
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration ruber dampers
8. BETAFPV Beta75X 2S Whoop Quadcopter (XT30) - DSMX
Feature
BETAFPVBETAFPV_313359_DSMX
Description
BETAFPV Beta75X 2S Whoop Quadcopter (XT30) - DSMXBULLET POINT
Beta75X start a new era of 2S whoop drones. With a big improvement in power, you could fly real acro, like a larger quad, but is still small enough, safe enough, and quiet enough to fly anywhere.
With the high performance STM32F405 processor FC boards and tuned Betaflight Ominibus 3.5.0 firmware, everyone could fly the Beta75X drone like a racing professor.
Durable and light enough frame is customed for the Beta75X. A total weight of 41g give pilots a good balance of weight and nice punch on 2S battery.
Whole drone no soldering or tinkering necessary. Customed lightest 1103 11000KV motors with cable connectors. Just plug and play.
300mAh 2S high rate battery is recommend in default. But pilot could also use their whoop batteries with a replaced power cable. Optional and affordable.
SPECIFICATION
Weight: 41g (without battery)
Motors: 1103 11000KV with connector
Props: 40mm 4-blades props, 1.5mm shaft hole
Camera tilt angle: 35 degree
Recommend battery: 300mAh 2S battery
Receiver Option: Frsky XM+ / FullSpeed DSMX / Futaba S-FHSS / Flysky
Battery:350mah 2S Battery / 300mah 1S Battery
PACKAGE
1 * Beta75X BNF 2S Whoop Quadcopter
1 * Spare 40mm 4-blades props (2CW+2CCW)
1 * 350mAh 2S 35C-70C battery (Not for PNP version) / 2 * 300mAh 1S Lipo HV batteries (Not for PNP version)
1 * Spare Canopy
9. BETAFPV F4 FC 1S Brushless Flight Controller ESC OSD Smart Audio (No RX) FPV Tiny Whoop Micro Racing Drone Beta75pro Beta65pro
Feature
This is upgraded F4 Brushless FC No RX based on F3 version, MCU has upgraded to STM32F411 100MHz with faster processing rate(from 72MHz to 100MHz). Build-in Betaflight OSD and polar reversed protection. Suitable for 1S brushless whoop drone Beta65 Pro, Beta75 Pro, BWhoop B06 etc.High-performance ST Microelectronics ARM Cortex-M4 core F411 100MHz CPU (safely overclocked to 120MHz).30A continuous drain current MOSFET. Lower to 8.5m inner resistance value (4.5V). It has a noticeable power improvement in low battery voltage status or with 8x20/8.5x20 motors.
The F4 1S brushless FC comes with no receiver, compatible receivers signal include PPM, SBUS, IBUS, Spektrum DSM2 / DSMX, 1024/2048 etc. The flight controller board comes pre-flashed with Betaflight firmware.
Fully programmable through Betaflight firmware, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings.
The output voltage for receiver is switchable between 3.3V and 5V. So pilots could use Spektrum receiver that need 3.3V power. 3.3V in default. Built in ESC support 5A continuous current and peak 6A (3 seconds), support BLHeliSuite programmable.Some basic guidance and typical FAQ, please check it here : https://betafpv.freshdesk.com/support/solutions
Description
BETAFPV F4 1S Brushless Flight Controller FPV FC Integrated with ESC OSD Support SmartAudio (No RX) for 1S FPV Micro Brushless Racing Drone like Beta75 pro Beta65 pro
Specifiction
FC
CPU: STM32F411CEU6 (100MHZ )
Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
Size: 26mm x 26mm, fully compatible with the Inductrix quad frame, BWhoop B06 frame and mounting pattern
Firmware version: betaflight_3.5.0_MATEKF411.hex
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 4g
ESC
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Recommend Parts List
Frame:
Beta65 Pro frame-www.amazon.com/dp/B078GLW4HK
Beta75 Pro frame-www.amazon.com/dp/B078H7R3PV
Props:
31mm 4-Blades props (for Beta65 Pro)-www.amazon.com/dp/B07D7WSL3L
40mm 4-blades props (for Beta75 Pro)-www.amazon.com/dp/B07B2P7TF4
Receiver: XM Receiver / XM+Receiver / Fullspeed DSMX Receiver / Futaba RX800-PRO Receiver / Flysky RX2A Pro Receiver
Motors:
0703 motors-www.amazon.com/dp/B078N93QVP
0603 motors-www.amazon.com/dp/B079HXLJJ5
Package List:
1 * F4 1S brushless flight controller
4 * M1.2x4mm screws
4 * M1.4x5mm screws
4 * Anti-vibration ruber dampers
Recent Comments